250 storefront series
2” x 4 1/2” SECTION
ALUMINUM STOREFRONTS PL-250 SERIES
The 250 presents itself as a versatile and budget-friendly center-glazed system, purpose-built to seamlessly incorporate 1-inch insulating glass. It boasts a comprehensive selection of extrusions and accessories, meticulously designed to accommodate a wide range of job conditions, ensuring adaptability and efficiency. The 250 glazing system is available in 2 x 4-1/2 sections, featuring a 1-1/4 glass pocket width. Notably, entrance doors can be easily customized through the use of a dedicated filler insert tailored specifically for this advanced glazing system. This design flexibility, combined with its economic advantages, makes the 250 an ideal choice for various architectural applications.
HANDLING, STORAGE AND PROTECTION OF ALUMINUM
The following precautions are recommended to protect the material against damage.
Following these precautions will help ensure early acceptance of your products and workmanship.
The mockup specimen for testing was a flat wall specimen, nominal one (1) story high, consisting of a 4 1/2″ deep, center glazed, aluminum window wall system, measuring approx, 10´ wide by 10´ high (3 lites wide by 2 lites high).
Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). The samples tested met the performance requeriments set forth in the referenced test procedures for a +1676/-2873 Pa (+35/-60psf) Design Pressure with missile impacts corresponding to Missile Level D and Wind Zone 3 for a basic protection rating.
The 250 presents itself as a versatile and budget-friendly center-glazed system, purpose-built to seamlessly incorporate 1-inch insulating glass. It boasts a comprehensive selection of extrusions and accessories, meticulously designed to accommodate a wide range of job conditions, ensuring adaptability and efficiency. The 250 glazing system is available in 2 x 4-1/2 sections, featuring a 1-1/4 glass pocket width. Notably, entrance doors can be easily customized through the use of a dedicated filler insert tailored specifically for this advanced glazing system. This design flexibility, combined with its economic advantages, makes the 250 an ideal choice for various architectural applications.
HANDLING, STORAGE AND PROTECTION OF ALUMINUM
The following precautions are recommended to protect the material against damage.
Following these precautions will help ensure early acceptance of your products and workmanship.
The mockup specimen for testing was a flat wall specimen, nominal one (1) story high, consisting of a 4 1/2″ deep, center glazed, aluminum window wall system, measuring approx, 10´ wide by 10´ high (3 lites wide by 2 lites high).
Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). The samples tested met the performance requeriments set forth in the referenced test procedures for a +1676/-2873 Pa (+35/-60psf) Design Pressure with missile impacts corresponding to Missile Level D and Wind Zone 3 for a basic protection rating.
IMAGE CAD BIM
IMAGE CAD BIM
250-Series (2 X 4-1/2 Center Glaze For 1 Glazing):
Performance: (Test sample of 10 feet (3048 mm) wide by 10 feet (3048 mm) high - 3 lites wide by 2 lites high).
a. Air infiltration:
Limit air leakage through fixed glazing and frames to 0.039 cfm/ft2/min when tested in accordance with ASTM E-283 at a cross pressure of 6.24 psf (0.30 kPa).
b. Water penetration under static pressure:
System shall not evidence uncontrolled water penetration at a cross pressure of 6 psf (0.29 kPa) when tested in accordance with ASTM-E331-00.
c. Uniform load structural per ASTM E 330:
Limit deflection to L/175. 1) Passed at Design Pressure of 20 psf (0.96 kPa).
EXAMINATION
- Do not begin installation until substrates have been properly
- If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
PREPARATION
- Clean surfaces thoroughly prior to
- Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
INSTALLATION
- Install in accordance with manufacturer’s
FIELD QUALITY CONTROL
- All joints between metal and masonry shall be fully caulked and field tested to resist water leakage with provisions taken to drain infiltrated water.
PROTECTION
- Protect installed products until completion of
- Touch-up, repair or replace damaged products before Substantial
PRL Glass Systems Inc
13644 Nelson Ave, Industry, CA. 91746
251 Mason Way, Industry, CA. 91746
PRL Aluminum Inc
14760 Don Julian rd, Industry, Ca. 91746
Quick Links
Oppening Hours
- Monday-Friday: 9am-6pm
- Sunday: Closed