Storefront

400 storefront series

1-3/4 x 4” SECTION

400 STOREFRONT SERIES

The 400 Series (1-3/4 x 4 system) stands out as a cost-effective system meticulously designed to meet industry-standard performance requirements efficiently. Featuring components designed for interchangeability, this series is versatile, suitable for both exterior and interior applications. It represents an industry-standard center-glazed system, seamlessly accommodating all standard entrance door hardware and door types, including those with single or double-action door hardware.

This system is capable of receiving ¼-inch glass within a ½-inch glass pocket width, providing flexibility for both shop and field fabrication. Additionally, the extrusions can be reinforced to meet more demanding performance requirements, ensuring durability and adherence to rigorous standards.

HANDLING, STORAGE AND PROTECTION OF ALUMINUM
The following precautions are recommended to protect the material against damage.
Following these precautions will help ensure early acceptance of your products and workmanship.

The mockup specimen for testing was a flat wall specimen, nominal one (1) story high, consisting of a 4 1/2″ deep, offset glazed, aluminum window wall system, measuring approx, 10´ wide by 10´ high (3 lites wide by 2 lites high). The system was glazed.

Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). The samples tested met the performance requeriments set forth in the referenced test procedures for a +1676/-2873 Pa (+35/-60psf) Design Pressure with missile impacts corresponding to Missile Level D and Wind Zone 3 for a basic protection rating.

The 400 Series (1-3/4 x 4 system) stands out as a cost-effective system meticulously designed to meet industry-standard performance requirements efficiently. Featuring components designed for interchangeability, this series is versatile, suitable for both exterior and interior applications. It represents an industry-standard center-glazed system, seamlessly accommodating all standard entrance door hardware and door types, including those with single or double-action door hardware.

This system is capable of receiving ¼-inch glass within a ½-inch glass pocket width, providing flexibility for both shop and field fabrication. Additionally, the extrusions can be reinforced to meet more demanding performance requirements, ensuring durability and adherence to rigorous standards.

HANDLING, STORAGE AND PROTECTION OF ALUMINUM
The following precautions are recommended to protect the material against damage.
Following these precautions will help ensure early acceptance of your products and workmanship.

The mockup specimen for testing was a flat wall specimen, nominal one (1) story high, consisting of a 4 1/2″ deep, offset glazed, aluminum window wall system, measuring approx, 10´ wide by 10´ high (3 lites wide by 2 lites high). The system was glazed.

Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). The samples tested met the performance requeriments set forth in the referenced test procedures for a +1676/-2873 Pa (+35/-60psf) Design Pressure with missile impacts corresponding to Missile Level D and Wind Zone 3 for a basic protection rating.

                                                     IMAGE                                                        CAD                                                            BIM

                                        IMAGE                                 CAD                               BIM

400-Series (1 3/4 X 4 Center Glaze For 1/4 Glazing):

Performance: (Test sample of 10 feet (3048 mm) wide by 10 feet (3048 mm) high – 3 lites wide by 2 lites high).

EXAMINATION
  1. Do not begin installation until substrates have been properly
  2. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.
  1. Clean surfaces thoroughly prior to
  2. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.
  1. Install in accordance with manufacturer’s
  1. All joints between metal and masonry shall be fully caulked and field tested to resist water leakage with provisions taken to drain infiltrated water.
  1. Protect installed products until completion of
  2. Touch-up, repair or replace damaged products before Substantial

explore all the productos

love the results

Discover our entire product gallery by clicking here

 

PRL Glass  Systems Inc
13644 Nelson Ave, Industry, CA. 91746
251 Mason Way, Industry, CA. 91746

PRL Aluminum Inc
14760 Don Julian rd, Industry, Ca. 91746

Oppening Hours
Newsletter